RC Car colours

Available in aerosols (150 ml) and airbrush (30 ml)

 

Ready to use, quick drying, fuel resitant light weight paint for racing, If wished for up-to 15 gr weight difference on a 1/10 scale race body, compard to pre-painted or water based coloured bodies (lower cenre of gravity)

Airbrush specifications:

Dilute with aceton

Applications:

RC Car Colours have been specially developed for the painting of Polycarbonate bodies. The special solvent used etches the surface, allowing the paint to bond permanently with the polycarbonate.

 

 

The colours in this colour chart are only colour indications!

* Before you begin ... Remove any dirt particles from the surface to be painted.

Polycarbonate bodies:

Cut out the body and sand the cut edges. Many bodies have a transparent protective foil on the outside. Do not remove this protective foil until the paints has dried! Mask all areas that are not to be painted, by using masking film or masking tape. First paint the dark and then the light colours so as to prevent the dark colours from shining through the lighter ones. Always check to make sure that the surfaces are dry and free of dust before painting!

For best results:

Before use, shake the can vigorously for approx. 2 min. until you hear the mixing ball rattling.

Spray at a distance of approx. 20 to 30 cm. While spraying make even cross movements with the can.

The covering capacity of RC Car Colours varies slightly from one colour to the next. Always spray one very light coat at a time to avoid bleeding. The final result is obtained after 2 to 3 coats. Wait approx. 5 min. before applying the next coat. Never spray just one heavy coat!

Allow the paint to dry for 5 minutes before removing the masking film and applying the next coat.

After use, turn the can upside down and spray for 2 sec. until the nozzle is empty.

Special instructions for fluorescent colours:

Fluorescent colours appear not to cover as well as normal colours. While spraying you must absolutely make sure to apply only very light coats. Always use at temperatures above 15°C. Spray from a distance of +/-15/20 cm. Allow the colour to dry for 30 min. and back the fluorescent colour with white RC Car Colour. Only then the desired fluorescent effect will be obtained!

Coloring of windows:

For coloring the windows you can use the RC Car Colours transparent smoke-Grey spray colour. Allow the entire painted body to dry for 10 min. before you paint the windows. Spray the transparent colour onto the body from a distance of approx. 30 to 40 cm. Make sure you apply only a very light coat of paint as bleeding around the windows might easily spoil the overall appearance of an otherwise beautifully painted body!

Special instructions for glitter colours:

Glitter colours are structured so that they must be sprayed first onto the body. Special care should be taken with these colours to apply very light coats only! These colours are only effect particles that are sprayed onto the body. These colours do not cover! Allow the applied glitter particles to dry for approx. 10 min. before covering them with a base colour.

 

Point of attention for RC Chrome:

The chrome effect depends on how carefully you follow the instructions! Recommended working temperature: +/- 20°C.Spray very thin even coats (+/-15) on your body with intervals of approx. 2 minutes. This in order to counter undesirable side-effects (matting). Then spray RC Car print & Chrome varnish or RC Car Colour Smoke 419 from a distance of approx. 30 cm in very thin coats (+/- 8) to seal the Chrome paint. NB: Do not sand in front when using chrome onto your body (scratch effect)

Points of attention for Sapphire and Jade:

use black RC car Colour 610 or any dark base-colour as backing coat.

---

 

RC模型車顏料

提供150毫升壓縮氣體樽裝及30毫升顏料噴筆

 

特性：隨時使用、快乾，防燃料腐蝕、重量輕的比賽用油漆，與已預塗或水性彩色顏料1/10的比賽車殼比較下，重量相差15克（有較低的重心）

 

噴筆規格：用丙酮稀釋

 

應用範圍：

RC模型車顏料專門開發給聚碳酸酯車殼使用，使用特殊溶劑蝕刻表面，使油漆永久黏附聚碳酸酯車殼上。

 

在這個彩色圖表上的顏色，僅供參考！

 

在你開始噴油前，首先從車殼表面移除任何灰塵顆粒。

 

聚碳酸酯車殼：剪出車殼和打磨切割邊緣。許多車殼都在外面有層透明保護膜，，直到油漆變乾前也不要撕除這個保護膜！使用遮蓋膜或膠帶遮蓋所有不希望上色的部份。首先噴上較深的顏色，其後才噴上較淺的顏色，這樣可以防止較深的顏色，穿透較淺的顏色。塗裝前經常檢查以確保表面乾燥且無灰塵！

 

最佳效果：

使用前，大力搖動瓶身 2分鐘，直到您聽到內裡小珠發出清脆咯咯聲。大約在20至30厘米距離噴塗，噴塗時同時均勻搖動瓶身。新一層顏色或會輕微影響下一層顏料，每次都薄薄的噴一層以避免不均勻情況。最終大約噴2至3層，其後等待約 5分鐘才噴新一層顏料，切勿只噴一層厚厚的顏料！讓油漆乾燥5分鐘後才撕除保護膜。完成後把瓶身上下倒轉並噴大約2秒，直到噴頭再沒有顏料。

 

螢光色的特別說明：

螢光色的遮蓋能力不及正常的顏色，所以噴塗時你必須確保每層都只是薄薄的噴上。在溫度高於15°C情況下使用，噴塗時保持+ / -15/20厘米的距離，其後讓顏色自然風乾30分鐘，最後噴上白色的顏料，那麼所需的螢光效果將特別明顯！

 

為窗口上色：

對於替窗口上色，您可以使用RC模型車顏料的透明煙灰色。首先讓車殼主色自然風乾大約10分鐘，其後才噴上窗口顏色。噴塗透明色時保持大約 30至40厘米的距離，並確保您只是薄薄的噴塗在窗口位置，否則很容易破壞整體外觀的油漆！

 

閃粉顏色特別說明：

閃粉顏色必須首先噴上車殼，特別注意這些顏色只可薄薄的噴上到車殼上產生粒子效果，並不能作為普通顏色般完全覆蓋！讓閃粉顏色自然風乾大約 10分鐘，然後噴上主底色。

 

電鍍顏色注意項：

電鍍的效果取決於你如何仔細按照說明所示！推薦工作溫度大約+ / - 20°C，噴塗時每層都必須保持薄身至大約15層，對您的車殼每隔約 2分鐘便噴上一層，這能避免發生不良的副作用影響，例如消光。然後噴塗RC模型車電鍍清漆或RC模型車煙霧色419，同時保持 30厘米的距離噴塗非常薄的塗層大約8層以密封電鍍顏色。注意：若使用電鍍顏色，開始製作時不要打磨您的車殼，這會影響電鍍效果。

 

使用藍寶石和翡翠顏色注意事項：

 

使用黑色的RC模型車顏料610或任何深色的顏料作為主底色。